称重传感器

称重传感器
称重传感器

产品类别

联系方式

电话:0755-26738591

传真:0755-26998440

网址:http://www.octsources.com

邮箱:sales@octsources.com

地址:深圳市南山区南头街道虹步路39号马家龙14栋大习科创大厦

产品类别 > 隔离器/转换器 > VT7-016D电压传感器

VT7-016D电压传感器

所属品牌:美国 OSI 来源:深圳市现代豪方仪器仪表点击:363次发布时间:2021-09-27

VT7-016D电压传感器


品牌:美国 OSI

型号:VT7

类型:直流电压传感器(直流至10KHZ频率范围)




描述/DESCRIPTION

VT7型直流电压传感器提供与输入成正比的输出。该装置主要用于测量和隔离直流电压,但也可用于监测交流和非正弦波形。输出信号是输入的缩放副本(交流输入=交流输出等)。对于交流或双向直流应用,必须使用具有双向输出类型的型号。可提供多种标准输入范围和输出类型。特殊范围请咨询工厂。

The model VT7 dc voltage transducer provides an output directly proportional to the input. It functions as a milliVolt shunt or high-voltage isolator.This unit is primarily intended to measure and isolate dc voltages, but may also be used to monitor ac and non-sinusoidal waveforms. The output signal is a scaled replica of the input (ac input = ac output, etc.). For ac or bidirectional dc applications, a model with bidirectional output type must be used.A wide variety of standard input ranges and output types are available. Consult factory for special ranges.



特征/FEATURES

•直流电压测量

•2500Vac介电测试

•宽频率范围

• dc voltage measurement

• 2500Vac dielectric test

• Wide frequency range



应用/APPLICATIONS

•准确测量和隔离直流电压

•并联隔离器

• Accurate measurement and isolation of dc voltages.







参数

电压输入

0-250mVdc,0-1000Vdc

输出

0-±5V,4-20mA,0-±10V,0-±1mA,0-±5Vdc,0-±10Vdc

准确性

±0.25% FS

频率

DC-10KHz

测量

直流/交流

系统配置

1Ø

 

 

*输入

(mV)

标准输出型号VT7

0-±1mA

4-20mA

0-±10V

0-±5V

*0-50

015B

015E

015D

015X5

*0-100

016B

016E

016D

016X5

*0-200

017B

017E

017D

017X5

*0-250

018B

018E

018D

018X5

输入

(伏特)

标准输出型号VT7

0-±1mA

4-20mA

0-±10V

0-±5V

0-10

001B

001E

001D

001X5

0-25

002B

002E

002D

002X5

0-50

003B

003E

003D

003X5

0-100

004B

004E

004D

004X5

0-150

005B

005E

005D

005X5

0-250

006B

006E

006D

006X5

0-300

007B

007E

007D

007X5

0-400

008B

008E

008D

008X5

0-500

009B

009E

009D

009X5

0-600

010B

010E

010D

010X5

**0-700

011B

011E

011D

011X5

**0-800

012B

012E

012D

012X5

**0-900

013B

013E

013D

013X5

**0-1000

014B

014E

014D

014X5

*分路输入.

**提供外部分隔盒.

仪器电源选项

选项“-11”......115Vac±15%,50/60Hz,5VA

选项“-22”......230Vac±15%,50/60Hz,5VA

选项“-12”、“-15”、“-24”、“-28”、“-37”、“-48”......12Vdc thru 48Vdc, ±10%, 150mA max.

 

标准型号包含通用开关电源。

“-11”和“-22”型号采用线性电源。




规格

输入INPUT

电压

0-250mVdc,0-1000Vdc

频率范围

dc-10kHz

超载

0.05-600V型号

2XF.S.或最大600Vac/850Vdc

700V-1000V型号(带外部分隔箱)

1.25XF.S.

负重

>100kΩ

介电测试DIELECTRIC TEST

输入/输出/案例

2500Vac

仪表功率INSTRUMENT POWER

标准

85-265Vac, 48-420Hz, 5VA or 110-370Vdc, 5VA

“-11”选项

115Vac±15%,50/60Hz,5VA

“-22”选项

230Vac±15%,50/60Hz,5VA

“-12”、“-15”、“-24”选项

12、15或24Vdc±10%,最大150mA

“-28”、“-37”、“-48”选项

28、37或48Vdc±10%,最大150mA

输出OUTPUT

响应(至90%)

50μs

加载

“B”型号

(0-1mA)

0-10kΩ

“D”、“X5”型号

(0-10,0-5V)

>2kΩ

“E”型号

(4-20mA)

0-500Ω

现场可调校准

±10%

精度ACCURACY包括线性、设定值和重复性的影响

所有型号

±0.25%F.S.@DC

温度TEMPERATURE

工作范围

-10°C ~ 60°C

影响

±1.0%Rdg., ±0.1%F.S.





连接图






















外壳尺寸



















安装/操作/保修/INSTALLATION / OPERATION / WARRANTY

 

 

 

安装说明/INSTALLATION INSTRUCTIONS

1.只能由合格的电工进行安装!

2.在进行任何电气连接之前,确保电气服务已断开。

3.支路保护按国家和地方规范要求设置检查机构的报告。

4.按要求布线,并按照本表和装置上的接线图固定到端子上。

5.传感器适合安装在600Vac线路上。

6.为防止与带电电路接触,当安装在裸母线上时,要求传感器安装在需要使用工具进入的外壳中。当安装在绝缘电缆上时不需要第二个外壳的电缆。

1. Installation should be performed by qualifi ed electricians only!

2. Make sure electrical service is disconnected before making any electrical connections.

3. Branch circuit protection is required to be provided in accordance with the National and Local codes of the inspection authority.

4. Route wires as required and secure to terminals per connection diagram on this sheet and on the unit.

5. Transducers are suitable for installation on 600Vac lines.

6. To prevent contact with live circuits, when installed on a bare bus bar, the transducer is required to be mounted in an enclosure that requires the use of a tool for access. When installed on an insulated cable this second enclosure is not required.

 

 

操作说明/OPERATING INSTRUCTIONS

1.本装置适用于海拔2000米以下的室内使用。

2.根据安装类别(过电压)II,污染等级2的瞬态过电压。

3.如果需要清洁外表面,则应断电所有供应服务(两个测量和仪表电源电路),并用软刷刷洗或用低压空气吹扫。使用适当的眼部保护。不适合清洗软管。

4.最高相对湿度80%,温度最高31ºC,线性下降至50% 40℃时的相对湿度。

5.最大工作温度范围为-20°C至60°C。

1. This unit is intended for indoor use at altitudes up to 2000 meters.

2. Transient overvoltages according to Installation Category (overvoltage) II, Pollution Degree 2.

3. If cleaning of the exterior surface is necessary, de-energize all services of supply (both measuring and instrument power circuits) and brush with a soft brush or blow off with low-pressure air. Use appropriate eye protection. Not suitable for hose-down cleaning.

4. Maximum relative humidity 80 percent for temperatures up to 31ºC decreasing linearly to 50 percent relative humidity at 40ºC.

5. Maximum operating temperature range is -20°C to 60°C.




浏览了该产品的用户还浏览:

3ACT-001A电流传感器

3ACT-005A换能器

3ACT-010A传感器

3ACT-020A电流传感器

3ACT-025A换能器

称重传感器客服
客服头部
称重传感器
称重传感器

扫一扫加微信公众号